Timken 70TPS130 thrust roller bearings

B1:212 mm; B2:52 mm; Fatigue load limit Pu:415 kN; B:150 mm; d1:400 mm; Reference speed:600 r/min; Ba min.:16 mm; Calculation factor e:0.22; K:12 mm; B5:66 mm;

D:55 mm; F:45 mm; db:44.5 mm; Limiting speed:10000 r/min; B:17 mm; ra max.:0.3 mm; Mass bearing:0.13 kg; s max.:0.8 mm; da:49.2 mm; Basic static load rating C0:46.5 kN;

Basic Interchange NDH:8505; Speed Rating-Single and Double Sealed Grease SDG:8500 rpm; Basic Interchange BCA:8505; Width - Overall B:15.9 mm; Old MRC Bearing Number:205FS; Width - Inner Ring B1:15.20 mm; Fillet Radius ra:1.00 mm; Basic Radial Load Rating-Static SCO:8000 N; d:25.000 mm; Basic Interch

D:51 mm; d:45 mm; Specific dynamic load factor K:10 N/mm²; Coefficient of friction µ max.:0.1; Tolerance shaft:h8; Specific static load factor K0:20 N/mm²; Permissible sliding velocity v min.:0.25 m/s; Mass bushing:0.13 kg; Tolerance housing:H7; Permissible sliding velocity v max.:5

B:30.20 mm; Grease Speed Rating n1:5000 rpm; Basic Static Radial Load Rating Co:39000 N; Accessories:Two Shields; d:45.000 mm; Fillet Radius ra:1.00 mm; D:85.0000 mm; Sealed Speed Rating n3:5000 rpm; Basic Dynamic Radial Load Rating C:48800 N; Oil Speed Rating n2:6700 rpm;

Grease:900 min-1; rs (min):1.5 mm; d:150 mm; dynamic Cr:281.840 kN; Pu:28.100 kN; d1:212 mm; D1:153 mm; H:50 mm; Oil:1 300 min-1; static Cor:835.000 kN;

Snap ring:SP 110; Limiting speed:9000 r/min; D:110 mm; Fatigue load limit Pu:1.53 kN; D4:116.6 mm; d:40 mm; Calculation factor f0:12; Ca max.:5.74 mm; r0 max.:0.6 mm; ba min.:3 mm;

Limiting speed:32000 r/min; Mass needle roller and cage assembly:0.0016 kg; Fatigue load limit Pu:0.63 kN; Basic static load rating C0:5.7 kN; Ew:13 mm; Reference speed:28000 r/min; Basic dynamic load rating C:4.57 kN; U:10 mm; Fw:10 mm;

Fatigue load limit Pu:0.655 kN; d1 ≈:46.1 mm; Calculation factor f0:14; Rubber seating ring:RIS 207 A; Hexagonal key size for grub screw N:3.969 mm; Basic dynamic load rating C:21.6 kN; C:19 mm; r1,2 min.:1 mm; d:34.925 mm; Thread grub screw G2:5/16-24 UNF;

d1:420 mm; Hydraulic nut:HMV 92 E; d:440 mm; Mass withdrawal sleeve:31 kg; A:9 mm; G2:G 1/4; B1:194 mm; Nut for removal:HM 3092; B2:205 mm; G1:35 mm;

D:90.0000 mm; d:50.000 mm; Sealed Speed Rating n3:4800 rpm; Grease Speed Rating n1:4800 rpm; B:30.20 mm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:39000 N; Oil Speed Rating n2:6300 rpm; Accessories:Two Shields; Basic Dynamic Radial Load Rating C:48800 N;

Accessories:One Seal; d:320.000 mm; Basic Dynamic Radial Load Rating C:172000 N; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:236000 N; Oil Speed Rating Open/Shielded n2:1600 rpm; Sealed Speed Rating n3:0 rpm; B:38.00 mm; D:400.0000 mm; Grease Speed Rating Open/Shielded n1:1300 rpm;

D:47.0000 mm; d:20.000 mm; Basic Static Radial Load Rating Co:10000 N; Set:Duplex Set DF; Basic Dynamic Radial Load Rating C:12100 N; Fillet Radius ra:0.80 mm; Lateral Eccentricity Max LE:0.003 mm; B:31.75 mm;

d:12.000 mm; Basic Dynamic Radial Load Rating C:7610 N; Fillet Radius rb:0.30 mm; D:32.0000 mm; Basic Static Radial Load Rating Co:3750 N; Oil Speed Rating n2:26000 rpm; Fillet Radius ra:0.64 mm; B:10.00 mm; Grease Speed Rating n1:18000 rpm;

Oil Speed Rating Open/Shielded n2:3200 rpm; Sealed Speed Rating n3:1700 rpm; Accessories:Two Shields & Snap-R; Basic Static Radial Load Rating Co:125000 N; Basic Dynamic Radial Load Rating C:125000 N; Grease Speed Rating Open/Shielded n1:2600 rpm; B:35.00 mm; Fillet Radius ra:2.00 mm; d:150.000 mm;